Self-organizing MESH
Multi-node, multi-hop networking can adjust routes as the topology changes.
CS2322 Series
Wireless video & data link · CS2322 series
CS2322-30 MESH Video Transmission Module
A software-defined radio module for self-organizing MESH networks, with factory-configured frequencies, flexible bandwidth and practical interfaces for UAV and ground-terminal integration.
30 dBmNominal TX designation*
40 MbpsPeak source-rated throughput
20 MHzMaximum listed bandwidth
AES-256Air-interface encryption
Overview
Flexible MESH Connectivity
Self-organizing networking and dynamic frequency selection for civil wireless video and data links.
Factory-set bands
Select a supported frequency band for the intended application and region.
Dynamic selection
Nodes can assess spectrum conditions and select frequencies from a preset list.
Flexible bandwidth
5, 10 or 20 MHz options; up to 40 Mbps is listed for 20 MHz.
AES-256 encryption
Air-interface encryption support for wireless data transmission.
Integration interfaces
Dual Ethernet and RS232, 3.3 V TTL and two RF connections.
Specifications
CS2322-30 Rated Values
Only CS2322-30 had a populated specification row in the supplied page; empty model rows were removed.
| Model | Power supply | Max. power draw | Source-listed TX rating | Reference distance | Weight |
|---|---|---|---|---|---|
| CS2322-30 | 24–28 V | 15 ± 5 W | 30 ± 3 dBm* | 25–45 km** | 180 g |
−40 to +55 °COperating temperature
−40 to +85 °CStorage temperature
5–95%Humidity, non-condensing
Installation & safety
- Connect TX/RX antennas as instructed. Operating without a TX antenna may damage the unit.
- Provide adequate heat dissipation during continuous operation.
- Received signal strength at a receiving port must not exceed +10 dBm.
- The supplied source recommends more than 2 m antenna separation between modules, including unpowered units.
- Power-consumption values were measured at room temperature with a 24 V supply and high-throughput traffic.
Configuration
Frequency & Bandwidth
Band selection is factory configured. Check local spectrum authorization for the intended operating region.
Frequency options
- 655 MHz: 635–675 MHz
- 815 MHz: 800–830 MHz
- 1350 MHz: 1300–1400 MHz
- 1400 MHz: 1350–1450 MHz
- 1475 MHz: 1420–1530 MHz
- 2450 MHz: 2400–2500 MHz
Custom frequency configurations may be available; confirm with CroSkylink before ordering.
Bandwidth & network
- 5 MHz: approximately one-quarter of the source-listed 20 MHz throughput.
- 10 MHz: approximately half of the 20 MHz throughput.
- 20 MHz: up to 40 Mbps, subject to conditions.
- Dynamic frequency selection operates within a preset list.
- Real-world data rate depends on RF and network configuration.
Performance
20 MHz Sensitivity & SNR
Source-listed values at 20 MHz. Swipe the table horizontally on smaller screens.
| Parameter | MCS0 | MCS1 | MCS2 | MCS3 | MCS4 | MCS5 | MCS6 | MCS7 | MCS8 |
|---|---|---|---|---|---|---|---|---|---|
| Single-antenna sensitivity (dBm) | −101 | −98 | −95 | −92 | −88 | −86 | −83 | −80 | −77 |
| Dual-antenna sensitivity (dBm) | −104 | −101 | −98 | −95 | −91 | −89 | −86 | −83 | −80 |
| Signal-to-noise ratio (dB) | −8 | −5 | −2 | 4 | 7 | 10 | 13 | 16 | 19 |
Connectivity
Interfaces & Ports
CS2322-30 connector information organized for integration review.
Ethernet · LAN1
PH2.0-4 · RX− / RX+ / TX− / TX+ · 10/100 Mbit/s.
Ethernet · LAN2
PH2.0-4 · RX− / RX+ / TX− / TX+ · 10/100 Mbit/s.
Dual RS232
PH2.0-6 · R1 / GND / T1 / R0 / GND / T0.
TTL serial
PH2.0-3 · R2 / GND / T2 · 3.3 V TTL.
Power input
XT30PW-M · GND / VCC · 24–28 V input.
RF ports × 2
SMA-K · RF Port 1 / RF Port 2.
Indicators
LED Indicator Guide
Five side-panel indicator positions, viewed with the digital interface facing down.
LED 1 · Power / FPGA
Green indicates normal power; red is used during FPGA download and turns off after completion.
LED 2 · Signal
From stronger to weaker: green → yellow → red → off.
LED 3 · Link
Green indicates link established; red indicates disconnection.
LED 4 · LAN1
Ethernet port 1 activity and status.
LED 5 · LAN2
Ethernet port 2 activity and status.
Mechanical
CS2322-30 Dimensions
The original model drawing is shown for enclosure and mounting reference.
Included
Accessory List
Source-listed accessories; confirm the final package before ordering.
Ethernet cables
PH2.0-to-RJ45 · 1.5 m × 2 pcs.
Serial cables
PH2.0 6-core · 0.2 m × 1 pc;
PH2.0 3-core · 0.2 m × 1 pc.
Power cable
XT30-to-DC · 0.3 m × 1 pc.
Ordering guide
Model Naming & Examples
CS2322-30-1400-4J2T
CS2322 — platform family
30 — nominal TX designation, dBm*
1400 — 1400 MHz center frequency
4J2T — 4 nodes, 2 hops
Listed MESH configurations
| Network topology | TX designation* | Frequency range | Example product model |
|---|---|---|---|
| 4 nodes / 2 hops | 30 dBm | 1350–1450 MHz | CS2322-30-1400-4J2T |
| 8 nodes / 1 hop | 30 dBm | 1350–1450 MHz | CS2322-30-1400-8J1T |
Use cases
Typical Applications
Examples for permitted civil deployments using the appropriate configuration.
UAV relay links
Connect authorized aerial and ground nodes in a configurable local MESH network.
Ground-terminal networks
Support mobile field stations and distributed inspection teams with adaptable links.
Emergency response
Set up temporary on-site communications where conventional infrastructure is unavailable.
Configure the right CS2322 link
Tell CroSkylink about your frequency, bandwidth, topology and integration needs, and request a verified power-limited configuration.
Contact CroSkylink